Abus AZ4110 LCD Keypad for Terxon SX_MX Installation Manual de usuario Pagina 171
- Pagina / 484
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
67
UK
081 Relay output OP1
To change the behaviour of relay output OP1 on the alarm
centre PCB:
1. On the control unit, enter:
081
2. The LCD display shows: 081: Bell
3. Via the keypad, select from the following items
and press:
00
Bell
This output is activated at local and
external alarms. Set the siren delay and
duration in menu items 41 and 42.
01
EE Follow
This output is activated if the entry/exit
delay is active. Note that this output is
not activated if the exit mode “internal”
is programmed to “silent” or
“immediate”.
02
Armed Lamp
This output is activated if the alarm
centre is completely or internally
activated.
03
Set Latch
This output is activated if the alarm
centre is completely or internally
activated. The output is also activated if
the alarm centre is reset or if a walk test
is started.
04
Shock sensor reset
This output is activated for 5 seconds at
the start of the exit delay.
05
Walk Test
This output is activated during the user
and programmer walk test. The output
is connected to the walk test input of
the motion sensor.
06
Ready Lamp
This output is activated if the alarm
centre is ready for complete or internal
activation. The alarm centre is ready
even if the zones with the properties
“entry/exit” or “entry to follow” are
opened.
07
24 Hour
This output is activated if a 24-hour
zone triggers an alarm. The output is
deactivated if the alarm centre is
deactivated.
08
Strobe
This output is activated if a local or
external alarm is triggered. The output
remains active until the alarm centre is
deactivated.
09
Smoke Reset
This output is used to reset smoke
detectors. This output is activated for at
least 3 seconds following every
deactivation and reset of the alarm
centre following an alarm.
10
Siren Test
This output is activated following
programming and during a siren test
(command 91 in the program menu).
11
Strobe Set
This output is activated for 10 seconds
after the alarm centre is activated and
the alarm centre is active. The output
can be used to issue an active
acknowledgement.
12
Set 1
This output is activated for a definable
time period (command 170) if the alarm
centre is activated completely (A) or
internally (B), (C) or (D) (command
171).
13
Unset 1
This output is activated for a definable
time period (command 172) if the alarm
centre is deactivated completely (A) or
internally (B), (C) or (D) (command
171).
14
Confirm
This output is active during a confirmed
alarm.
- 11863866 1
- 1 Einführung 2
- 2 Bestimmungsgemäße 2
- Verwendung 2
- 3 Inhaltsverzeichnis 3
- !WARNUNG! 5
- !ACHTUNG! 5
- NC-Alarmkontakte 9
- 9 Hinweise zur Montage 12
- 10.3 Platinenübersicht 15
- Anschluss Bedeutung 15
- 10.4.3 Rauchmelder 18
- 11 Einzelsystem oder 23
- partitioniertes System 23
- 12 Allgemeine Begriffe 24
- 13 Begriffserklärung 25
- 14 Beispielinstallation 27
- 0 und im 29
- 15 Erste Inbetriebnahme 33
- 16.1 Programmiermodus 34
- 099 und bestätigen Sie Ihre 34
- Nach180 Sek ausblenden 36
- 30Sek nach Code 36
- Prog. der Impulsausgänge 86
- Ereignisspeicher 93
- Ausgang 1 testen 94
- Ausgang 2 testen 94
- Ausgang 3 testen 94
- 16.7 SIA Report-Modus 96
- 17 Technische Daten 98
- 18 Fehlerbehebung 99
- 20 Systemplan 103
- 1 Introduction 106
- 2 Usage in accordance with 106
- regulations 106
- 3 Contents 107
- 4 Precautions 109
- 7 Notes on security system 112
- NC alarm contact 113
- Note for 230 V connection 115
- 9 Notes on installation 116
- 10 Notes on wiring 117
- 10.3 Detectors 120
- 10.3.3 Smoke detector 121
- 10.5 Dialler 123
- 10.6 Key switch 123
- Alarmpanel 125
- 11 Single system or 126
- 12 Term declaration 127
- 13 General terms 128
- 14 Specimen Installation 129
- 15 First-time usage 135
- 16 Programming 136
- Hide after 180 secs 138
- Hide 30 sec after code 138
- 101-158 for programming the 143
- Entry Meaning 193
- 2K1 2.2 KOhm resistor used 193
- 4K7 4.7 KOhm resistor used 193
- Summary 195
- Intermediate 195
- 17 Technical data 196
- 18 Troubleshooting 197
- 20 System plan 200
- 2 Utilisation conforme 202
- 3 Table des matières 203
- 4 Consignes de sécurité 205
- Contacts d’alarme 209
- 9 Instructions de montage 212
- 10.1 Centrale 213
- 10.2 Elementes de commande 214
- 10.3 Détecteurs 217
- 10.3.3 Détecteurs de fumée 218
- 10.5 Transmetteur 220
- 11 Système unique ou 223
- 12 Terminologie 224
- 13 Terminologie générale 225
- 14 Exemple d’installation 226
- 15 Première mise en service 232
- 16 Programmation 233
- Mémoire d’événements 295
- Tester la sortie 1 296
- Tester la sortie 2 296
- Tester la sortie 3 296
- 099 pour quitter le menu de 297
- MODE = De base 298
- MODE = Récapitulatif 299
- MODE = Intermédiaire 299
- MODE = Total 299
- 17 Fiche technique 300
- 18 Dépannage 301
- 19 Index 302
- 20 Plan du système 304
- 1 Inleiding 306
- 2 Bedoeld gebruik 306
- 3 Inhoud 307
- 4 Veiligheidstips 309
- Kruiskopschroevendraaier 310
- Verteiler 313
- NC-Alarmkontakt 313
- (z.B. Öffnungsmelder) 313
- 9.1 De centrale 316
- 9.2 De bedieningselementen 316
- 10.2 Bedieningselementen 318
- 10.3 Melders 321
- 10.3.3 Rookmelders 322
- 10.5 Kiezer 324
- 10.6 Sleutelschakelaar 324
- 10.8 Relaismodule 325
- 10.9 Weerstanden 325
- 10.10 Aansluiting van 326
- 10.11 Looptest 326
- 10.12 Melder-alarmgeheugen 326
- 11 Enkel systeem of 327
- 12 Begripsverklaring 328
- 13 Algemene begrippen 330
- 14 Voorbeeldinstallatie 331
- 15 De eerste keer in gebruik 337
- 16.1 Programmeermodus 338
- Na 180sec. uitschakelen 340
- 30sec. na code uitschakelen 340
- 000 Landinstellingen 347
- 001 – 008 zone-instelling 348
- 029 Toegangsalarmvertraging 352
- 030 Stille overval 352
- 031 Zonesabotage 353
- 033 Systeem-reset 353
- 034 Overval-reset 353
- 035 Eerste-alarmreactie 354
- 036 Alarm afbreken 354
- 038 Systeemsabotage-reset 355
- 040 Systeem auto op scherp 356
- 041 Sirenevertraging 356
- 042 Sireneduur 356
- 046 Sabotagealarm 357
- 051 Datum en tijd 358
- 052 Sabotage blokkeren 358
- 053 Afbreken - reset 358
- 081 Transistoruitgang OP1 364
- 082 Transistoruitgang OP2 366
- 083 Transistoruitgang OP3 366
- 085 Inbraakuitgang 366
- 126 Taal instellen 368
- 128 Extern alarm 368
- 129 Extern deactiveren 368
- ingangsvertragingstijd 3/4 373
- 16.4 Testfunctie 374
- Gebeurtenisgeheugen 374
- Uitgang 1 testen 376
- Uitgang 2 testen 376
- Uitgang 3 testen 376
- Luidsprekeruitgang testen 376
- 17 Technische gegevens 378
- 18 Fouten verhelpen 379
- 20 Systeemoverzicht 382
- 1 Introduktion 384
- 2 Korrekt anvendelse 384
- 3 Indhold 385
- !ADVARSEL! 387
- NC-alarmkontakter 391
- 9 Monteringsoplysninger 394
- Schni ttstel le 397
- 10.4.3 Røgalarmer 400
- 12 Generelle begreber 406
- 13 Begrebsforklaring 406
- 14 Eksempelinstallation 408
- 15 Første ibrugtagning 414
- 16.1 Programmeringsmodus 415
- Fjern efter 180 sek 417
- Fjern 30 sek efter kode 417
- Prog. af impulsudgangene 467
- indgangsforsinkelsestid 3/4 471
- Hændelseshukommelse 474
- Test udgang 1 475
- Test udgang 2 475
- Test udgang 3 475
- Test højtalerudgang 475
- 16.7 SIA-rapportmodus 477
- 17 Tekniske data 479
- 18 Fejlhjælp 480
Relacionado con productos y manuales para Para Casa Abus AZ4110 LCD Keypad for Terxon SX_MX Installation
(2 paginas)
(76 paginas)Vision Controls PC/workstation barebones user manuals
The list of Vision Controls PC/workstation barebones products contains 6 user manuals for 1 models. All pdf user’s guides are available for download or viewing online.
Comentarios a estos manuales