Abus FU8403 Wireless Display Module Manual de usuario descargar pdf (Pagina 12)

12

4.

Teaching one detector (Submenu LED

01):

a)

Press SELECT key

1

once:

Main menu

LED

01

is shining

green

b)

Press SET key

2

once: Submenu LED

01

(teach

alarm) opens

The LED

in the first

free zone shines

green

(if no alarm

has been

taught,

LED

01

is always shining green). Zones already occupied flash red

and cannot

be selected

with the

SELECT key.

If no

more free zones are available,

the

LED does

not shine

c)

The zone you

want to

teach

the

detector

to

can be selected

with

SELECT key

1

d)

SET key

2

opens

the zone

LED flashes green (ready

for learning)

e)

Open

the

tamper contact

on

FTS

96

E

or

wireless magnetic contact

by

removing

the cover

(to do that, the battery

must be

fitted to the

FTS

96

E

or

wireless

magnetic contact)

f)

The radio signal is emitted

and the

detector is

taught to the

zone;

an

acoustic acknowledgement

follows

g)

The

next

free zone is

then

indicated

with the

green LED

h)

For teaching

additional

detectors, see Point

4 c

i)

Exit

the

menu using

ESC key

3

5.

Deleting

a

taught detector (Submenu LED

02):

a)

Press SELECT key

1

once:

Main menu

LED

01

is shining

green

b)

Press SELECT key

1 once

LED

02

shines

green

c)

Press SET key

2

once: Submenu LED

02

(delete detector)

opens

The LED

in the first

assigned

zone

flashes

orange

d)

You can select

the

detector you

want to

delete

with

SELECT key

1

e)

Press SET key

2

(LED flashes more quickly)

until the

LED goes

out

detector

deleted

f)

The

next

assigned zone

then

is indicated

by the

flashing orange LED

g)

To delete

additional

detectors, see Point

5 d)

h)

Exit

the

menu

with

ESC key

3 or

automatically

after

deleting

the last

assigned

zone

6.

Radio signal strength indicator (Submenu LED

03):

a)

Press SELECT key

1

once:

Main menu

LED

01

is shining

green

b)

Press

the

SELECT key

1 twice:

LED

03

shines

green

c)

Press SET key

2

once: Submenu LED

03

(Radio signal strength

indicator) opens

The LED

in the first

assigned zone shines

green

d)

Use SELECT key

1 to

select

the

detector

for the last

received radio signal level you

want to display

e)

Press SELECT key

1

once: The last received signal strength

of the first

assigned zone is displayed

via the number

of

shining

LEDs

starting with

LED

16; the

more LEDs shine,

the

higher

the

received radio signal

strength.

To ensure permanently secure radio reception,

at

least three LEDs should be

shining

f)

The

next

zone can be tested

with the

SELECT key,

etc.

g)

Exit

the

menu using

ESC key

3

7.

Delete

all

/

Factory reset (Submenu LED

16):

a)

Press SELECT key

1

once:

Main menu

LED

01

is shining

green

b)

Press SELECT key

1

three

times:

LED

16

shines

green

c)

Press SET key

2

once: Submenu LED

16

(factory reset)

opens

LEDs

01

–

16

flash

red

d)

Keep SET key

2

pressed (LEDs flash faster)

until all

LEDs

01

–

16 go out

e)

The radio controlled display module automatically returns

to the

display

mode

Notes:

The radio controlled display module automatically returns

to the

display mode

if no activity

has

occurred

for a

period

of

ca.

3

minutes

(no

keys were pressed

and no

detector was

taught).

If no

radio signal has been detected

from the

respective radio

alarm for

ca.

15 minutes,

a

supervision error is indicated

by the

red LED

18 and the

respective zone LED flashing

green.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 49 50

Comentarios a estos manuales

Sin comentarios