Abus FU8007 Secvest 2WAY Base Kit Installation Manual de usuario Pagina 16
- Pagina / 106
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
16
3.2 Checking the detector range
End training by pressing Next and going Back to the main menu. Go to Installer
Menu Æ Test Æ Walk Test and carry out a walk test by triggering an alarm
message (A).
As smoke detectors do not have a tamper contact, only the alarm is displayed (A).
The display with the number of tested zones without tamper contacts remains.
On detectors with tamper switches, the tamper message is displayed (T), then the
alarm display (A) when the detector is triggered.
Select Test Select Walk Test
Trigger an
alarm (A).
“A” is shown next to the trained smoke detectors. “T” is displayed next to detectors
with tamper contacts.
Go to the floor where installation is to be made and trigger the previously trained
detectors.
“A” should be shown next to every zone.
3.3 Checking the signal strength of the detector
The detector signal strength test is made in the same way as the walk test.
The displayed signal strength corresponds to the reception strength of the last
received signal on this detector.
The signal strength must be higher than 3 for satisfactory wireless communication. If
the detector signal is too weak, use a repeater (accessory module) to ensure good
wireless communication.
Select the Detector Signals menu item.
The signal strength is displayed next to the tested zone.
The signal strength display is automatically updated every 5 minutes.
Information:
All zones tested
T = Tamper
A = Alarm
Number of zones
to be tested
- Secvest 2WAY 1
- Introduction 2
- Contents 3
- 1.1 Cellar installation 8
- 1.2 Ground floor installation 9
- 1.3 Top floor installation 10
- 1.4 Number of components 11
- 1.5 Detector list 12
- 2. Installing the system 13
- 2.1 230 V a 13
- 50 Hz mains connection 13
- 2.2 PSTN telephone connection 14
- 3. Training the detectors 14
- a b 14
- Detector list 15
- 3.1 Assigning the zone name 15
- In the installer menu: 17
- Info module 17
- 3.8 Informing other persons 22
- 3.9 Signaller 22
- 1234 (default) 23
- User menu 24
- Select the “User” menu item 24
- 26
- WARNING! 32
- Caution! 32
- IMPORTANT 32
- INFORMATION! 32
- !WARNING! 33
- !IMPORTANT 33
- Alarm centre characteristics: 34
- 8.5 Assembling the base plate 36
- 8.11 Closing the alarm centre 39
- 8.13 Final tasks 39
- 9. Explanation of terms 40
- 01/05/2008 42
- 12. Installer menu 43
- 13. Adding detectors 44
- 13.1 Auto learn 44
- 13.3 Detector already in use 46
- 13.4 Delete All 46
- 13.7 Assigning the zone name 48
- 13.8 Selecting the zone type 49
- 13.9 Selecting partitions 50
- 14. Outputs 52
- 14.1 Adding outputs 52
- 14.2 Editing outputs 53
- 14.4 Invert output 54
- , for example 56
- 15. Other Devices 57
- 15.1 External siren 58
- 15.2 Info Module/Int Siren 59
- 15.2.1 Updates / Disabled 59
- 15.2.2 Rdy-to-Set LED 60
- 15.3 Add WAM 60
- 15.3.2 WAM as output module 62
- 15.3.4 WAM as siren module 62
- 15.4 Arming station 62
- Select the arming station 63
- Instant Set Y 64
- 16. Partitions 67
- 16.1 Partition types 67
- 17. System options 69
- 17.1 User access 70
- 17.3 Selecting a language 72
- 17.4 Default settings 72
- 17.5 Installer code 72
- 17.13 Jamming 74
- 17.14 Batt Load Test 74
- 17.15 Siren in PSet 74
- 17.16 Force Set 75
- 17.17 RF Siren Options 75
- 17.18 Tamper alarm 75
- 18. IP Network 76
- 19. Download settings 77
- 19.1 Account Name 77
- 19.2 Connection Type 77
- 19.3 Rings to Answer 78
- 19.4 Answer on 1 ring 78
- 19.5 Access Mode 78
- 19.6 Phone Book 78
- 19.7 IP Network 79
- 19.8 Secure Callback 79
- 19.9 Modem Baud Rate 79
- 20. Reporting 79
- 20.1 Alarms 80
- 20.1.1 Call mode 81
- 20.1.2 Primary telecoms 81
- 20.1.3 Phone Book (ALARMS) 81
- 20.1.4 IP-Network 81
- 20.1.6 Report Type 82
- 20.1.7 Fast Format Channel 82
- 20.1.5 Account numbers 82
- 20.1.8 FF Report Restorals 83
- 20.1.9 SIA Report Mode 83
- 20.1.10 SIA Report Restorals 84
- 20.1.11 Contact ID Reports 84
- 20.1.12 Force Test Call Now 85
- 20.1.13 Dynamic Test Call 85
- 20.1.14 Static Test Call 85
- 20.1.15 Burg-Comms-Rearm 86
- 20.1.16 Send Tamper as Burg 86
- 20.1.17 No Transmission 86
- 20.2 Social Care 86
- 20.2.1 Call Mode 87
- 20.2.2 Primary Telecoms 87
- 20.2.4 Account Numbers 87
- 20.2.5 Report Type 88
- 20.2.6 Call Acknowledge 88
- 20.3 Speech Dialler 88
- 20.3.1 Call Mode 89
- 20.3.2 Primary Telecoms 89
- 20.3.3 Messages 89
- 20.3.4 Phone Book 89
- 20.3.5 Trigger 89
- 20.3.6 Destinations 90
- 20.3.7 Call Acknowledge 90
- 20.4 SMS 91
- 20.4.1 Call Mode 91
- 20.4.2 Primary Telecoms 91
- 20.4.3 Messages 91
- 20.4.4 Phone Book 92
- 20.4.5 SMS Triggers 92
- 20.4.6 PSTN SMS 92
- 20.4.7 Destinations 93
- 20.5 Reporting Options 93
- 20.5.1 Line Fault 93
- 20.5.2 GSM Omit Digit 94
- 21. Social Care 95
- 21.1 Start/End Monitoring at 95
- 21.2 Monitoring Interval 95
- 21.3 Set Volume 95
- 22. Test function 95
- 22.1 Testing the local siren 96
- 22.2 Testing the loudspeaker 96
- 22.3 Testing the keypad 96
- 23. Viewing the log 98
- 24. About Panel 98
- 26. Fitting the ISDN module 100
- 27. Fitting the GSM module 100
- 29. Fitting the GPRS module 101
- 30. Final tasks 102
- 31. Module certification 102
- 32.2 Programming 103
- 33. Technical data 103
- 34. Declaration of conformity 104
- 35. Glossary 105
Relacionado con productos y manuales para Para Casa Abus FU8007 Secvest 2WAY Base Kit Installation
(80 paginas)
(110 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales